Unidad 6

Programa 1

15/11/2022    "blink"
/*
  Blink

  Turns an LED on for one second, then off for one second, repeatedly.

  Most Arduinos have an on-board LED you can control. On the UNO, MEGA and ZERO
  it is attached to digital pin 13, on MKR1000 on pin 6. LED_BUILTIN is set to
  the correct LED pin independent of which board is used.
  If you want to know what pin the on-board LED is connected to on your Arduino
  model, check the Technical Specs of your board at:
  https://www.arduino.cc/en/Main/Products

  modified 8 May 2014
  by Scott Fitzgerald
  modified 2 Sep 2016
  by Arturo Guadalupi
  modified 8 Sep 2016
  by Colby Newman

  This example code is in the public domain.

  https://www.arduino.cc/en/Tutorial/BuiltInExamples/Blink
*/

// the setup function runs once when you press reset or power the board
int led=13;
void setup() {
  // initialize digital pin LED_BUILTIN as an output.
  pinMode(13, OUTPUT);
}

// the loop function runs over and over again forever
void loop() {
  digitalWrite(13, HIGH);   // turn the LED on (HIGH is the voltage level)
  delay(10000);                       // wait for a second
  digitalWrite(13, LOW);    // turn the LED off by making the voltage LOW
  delay(500);                       // wait for a second
}

Programa 2

16/11/2022      "hola1"
void setup() {
  // put your setup code here, to run once:
Serial.begin(9600);
Serial.print("Hola");
}

void loop() {
  // put your main code here, to run repeatedly:

}

Programa 3

16/11/2022    "hola2"
void setup() {
  // put your setup code here, to run once:
Serial.begin(9600);
}

void loop() {
  // put your main code here, to run repeatedly:
Serial.println("Hola loop");
}

Programa 4

16/11/2022     "Variable1"
//global
int a=42;
char c='m';
float raiz;
void setup() {
  // put your setup code here, to run once:
Serial.begin(9600);
raiz=sqrt(2.0);
Serial.println(a);
Serial.println(c);
Serial.println(raiz);
}

void loop() {
  // put your main code here, to run repeatedly:

}

Programa 5

16/11/2022     "Variable2"
//global
int a=42;
char c='m';
float raiz;
void setup() {
  // put your setup code here, to run once:
Serial.begin(9600);
raiz=sqrt(2.0);
Serial.println(a);
Serial.println(c);
Serial.println(raiz);
}

void loop() {
  // put your main code here, to run repeatedly:

}

Programa 6

16/11/2022     "Variable3"
int a=42;
char c='m';
float raiz;

void setup() {
// put your setup code here, to run once:
Serial.begin(9600);

}

void loop() {
// put your main code here, to run repeatedly:
raiz=sqrt(2.0);
Serial.println(a);
Serial.println(c);
Serial.println(raiz);
}

Programa 7

16/11/2022     "Variable4"
void setup() {
// put your setup code here, to run once:
Serial.begin(9600);
float r=0.75;
float c=2.0*PI*r;
Serial.print("CIRCUNFERENCIA= ");
Serial.println(c);
}

void loop() {
// put your main code here, to run repeatedly:

Programa 8

16/11/2022     "Variable5"
void setup() {
// put your setup code here, to run once:
Serial.begin(9600);
float r=0.75;
float a=PI*r*r;
Serial.print("AREA= ");
Serial.println(a);
}

void loop() {
// put your main code here, to run repeatedly:

}

Programa 9

16/11/2022     "Constante 1"
const int VAR1=1;
const int VAR2=10;
const int BAU=9600;
//CALVO, PELO LARGO, SOMBRERITO CALVO
void setup() {
// put your setup code here, to run once:
Serial.begin(BAU);
for(int i=VAR1;i<=VAR2;i++)
{
Serial.println(i);
delay(500);
}
Serial.print("TERMINO");
}

void loop() {
// put your main code here, to run repeatedly:

}

Programa 10

17/11/2022     "If1"

const int BAU=9600;
void setup() {
  // put your setup code here, to run once:
Serial.begin(BAU);
int a=42;
int b=42;
if(a>b)
{
    Serial.print ("A es mayor");
}
else if(a<b)
  {
  Serial.print("A no es mayor que B");
  }
  else
  {
  Serial.print ("A es igual a B");
  }
}

void loop() {
  // put your main code here, to run repeatedly:

}


Serial.println(raiz);
}

void loop() {
  // put your main code here, to run repeatedly:

}

Programa 11

17/11/2022     "If2"

const int BAU=9600;
void setup() {
  // put your setup code here, to run once:
Serial.begin(BAU);
int a=42;
int b=42;
if(a>b)
{
    Serial.print ("A es mayor");
}
else if(a<b)
  {
  Serial.print("A no es mayor que B");
  }
  else
  {
  Serial.print ("A es igual a B");
  }
}

void loop() {
  // put your main code here, to run repeatedly:

}


Programa 12

17/11/2022     "If3"

const int BAU=9600;
void setup() {
  // put your setup code here, to run once:
Serial.begin (BAU);
int a=89;
int b=42;
if ((a>50)&&(b<50)){
  Serial.print("Rango normal");
}
else Serial.print("Rango anormal");
}

void loop() {
  // put your main code here, to run repeatedly:

}

Programa 13

17/11/2022     "If4"

const int BAU=9600;
void setup() {
  // put your setup code here, to run once:
Serial.begin(BAU);
int a=101;
int b=-2;
if ((a>100) || (b<0)){
  Serial.print("Wow puede ser peligroso");
}
}

void loop() {
  // put your main code here, to run repeatedly:

}


Programa 14

17/11/2022     "If5"

const int BAU=9600;
void setup() {
  // put your setup code here, to run once:
  Serial.begin(BAU);
  int a=101;
  int b=101;
  if((a>100)||(b<0)){
    Serial.print("WOW! puede ser peligroso");
  }
  else if (a==b){
    Serial.print("Tal vez debas correr");
  }
  else
  Serial.print("A salvo");
}

void loop() {
  // put your main code here, to run repeatedly:

}


Programa 15

17/11/2022     "If6"


const int BAU=9600;
void setup() {
  // put your setup code here, to run once:
Serial.begin(BAU);
int a=56;
int b=56;
if ((a>100) || (b<0)){
  Serial.print("Wow puede ser peligroso");
}
else if (a==b) 
{
  Serial.print("Tal vez debes de correr");
}
else 
Serial.print("A SALVO");
}

void loop() {
  // put your main code here, to run repeatedly:

}


Programa 16

17/11/2022     "If7"

byte x=50;
const int BAU=9600;
void setup() {
  // put your setup code here, to run once:
Serial.begin(BAU);
if (x>=10 && x<=20){
  Serial.print("Frase 1 ");
}
if (x>=10 || x<=20){
Serial.print("Frase 2 ");
}
if (x>10 && !(x<=20)){
Serial.print("Frase 3 ");
}
}

void loop() {
  // put your main code here, to run repeatedly:

}


Programa 17

18/11/2022     "if8 "

String cad1="Hola";
String cad2="Holus";
const int BAU=9600;
void setup() {
  // put your setup code here, to run once:

}

void loop() {
  // put your main code here, to run repeatedly:

}


Programa 18

18/11/2022     "If9"

int numero;
const int BAU=9600;
void setup() {
  // put your setup code here, to run once:
Serial.begin (BAU);
}

void loop() {
  // put your main code here, to run repeatedly:
delay(500);
if (Serial.available()>0){
  numero=Serial.parseInt ();
if (numero=69){
  Serial.print("Le atinaste");
}
else if(numero<69){
  Serial.print("Frio");
}
else (Serial.print("Caliente"));}
}   


Programa 19

18/11/2022     "while 1"

byte x=1;
const int BAU=9600;
void setup() {
  // put your setup code here, to run once:
Serial.begin(BAU);
}

void loop() {
  // put your main code here, to run repeatedly:
while (x<=50){
  Serial.println (x++);
  x=x+1;
  delay(250);
}
}

Programa 20

18/11/2022     "while 2"

byte x=1;
const int BAU=9600;
void setup() {
  // put your setup code here, to run once:
Serial.begin(BAU);
}

void loop() {
  // put your main code here, to run repeatedly:
while (true){
  Serial.println (++x);
if  (x==7){
  Serial.print
}
Serial.print("tan tan");
break;
  delay(250);
}
}

Programa 21

18/11/2022     "while 3"

byte x=1;
const int BAU=9600;
void setup() {
// put your setup code here, to run once:
Serial.begin(BAU);
while(true)
{
Serial.println(++x);
if (x==7)
{
Serial.print("TAN TAN");
break;
}
delay(250);
}
}

void loop() {
// put your main code here, to run repeatedly:
/*while(true)
{
Serial.println(++x);
if (x==7)
{
Serial.print("TAN TAN");
break; //NO TIENE SENTIDO USAR BREAK EN UN LOOP
}
delay(250);
}*/
}

Programa 22

18/11/2022     "for 1"

byte x=1;
const int BAU=9600;
void setup() {
  // put your setup code here, to run once:
Serial.begin(BAU);
for (int i=1; i<=10; i++){
  Serial.println(i);
    delay(250);
  }
  Serial.println("Tan tan del for");

}

void loop() {
  // put your main code here, to run repeatedly:

}


Practicas con el Arduino

Programa 1

22/11/2022     "LED 1"
const int BAU=9600;
void setup() {

  // put your setup code here, to run once:
Serial.begin (BAU);
pinMode (13,OUTPUT);
pinMode (12,OUTPUT);
pinMode (11,OUTPUT);
}
void loop() {
  // put your main code here, to run repeatedly:
digitalWrite (13,HIGH);
delay (500);
digitalWrite (13,LOW);
delay (250);
digitalWrite (12,HIGH);
delay (500);
digitalWrite (12,LOW);
delay (250);
digitalWrite (11,HIGH);
delay (500);
digitalWrite (11,LOW);
delay (250);
}




Programa 2

28/11/2022     "LED 2"

int lr=13;
int lv=12;
int la=11;
int num;
void setup() {
  // put your setup code here, to run once:
Serial.begin (9600);
pinMode (lr,OUTPUT);
pinMode (lv,OUTPUT);
pinMode (la,OUTPUT);
}

void loop() {
  // put your main code here, to run repeatedly:
if (Serial.available()>0){
  Serial.println("1.Rojo");
  Serial.println("2.Amarillo");
  Serial.println("3.Azul");
  Serial.println("4.Salir");//Aqui nunca sale 
  num=Serial.parseInt ();
  Serial.print("Numero");
  Serial.println(num);
if (num==0)
{
 digitalWrite(lr,LOW);
 digitalWrite(lv,LOW);
 digitalWrite(la,LOW); 
}
else
{ if(num==1)
  {
 digitalWrite(lr,HIGH);
 digitalWrite(lv,LOW);
 digitalWrite(la,LOW);
 delay (250); 
  }
else
{ if(num==2)
  {
 digitalWrite(lr,LOW);
 digitalWrite(lv,HIGH);
 digitalWrite(la,LOW);
  delay (250);
  }
else
{ if(num==3)
  { 
 digitalWrite(lr,LOW);
 digitalWrite(lv,LOW);
 digitalWrite(la,HIGH);
 delay (250);
  } }
  } 
}
}
}





Programa 3

28/11/2022     "LED RGB 1"

const int redPin=11;
const int greenPin=9;
const int bluePin=10;
void setup() {
  // put your setup code here, to run once:
  pinMode(redPin,OUTPUT);
  pinMode(greenPin,OUTPUT);  
  pinMode(bluePin,OUTPUT);  
  Serial.begin(9600);
  Serial.println("Dame colores en RGB (ej. 255 100 200)");
 }

void loop() {
  // put your main code here, to run repeatedly:
  if(Serial.available()){
    int red=Serial.parseInt();
    int green=Serial.parseInt();
    int blue=Serial.parseInt();
    analogWrite(redPin,red);
    analogWrite(greenPin,green);
    analogWrite(bluePin,blue);
    }
  }






Programa 4

29/11/2022     "LED RGB 2"


const int redPin=11;
const int greenPin=9;
const int bluePin=10;
int num;
int sel;
void setup() {
  // put your setup code here, to run once:
  pinMode(redPin,OUTPUT);
  pinMode(greenPin,OUTPUT);  
  pinMode(bluePin,OUTPUT);  
  Serial.begin(9600);
     Serial.println("Escoge el color que te sea de tu preferencia: ");
    Serial.println("1. Rojo ");
    Serial.println("2. Morado");
    Serial.println("3. Verde");
    Serial.println("4. Azul ");
    Serial.println("5. Rosa ");
    Serial.println("6. Salir");
 }

 
void loop() {
  // put your main code here, to run repeatedly:
  if(Serial.available()){
    int red=Serial.parseInt();
    int green=Serial.parseInt();
    int blue=Serial.parseInt();
    analogWrite(redPin,red);
    analogWrite(greenPin,green);
    analogWrite(bluePin,blue);
    }
  

    sel=Serial.parseInt();
    if (sel==1){
    analogWrite(redPin,220);
    analogWrite(greenPin,000);
    analogWrite(bluePin,000);
    }  
       if (sel==2){
    analogWrite(redPin,200);
    analogWrite(greenPin,200);
    analogWrite(bluePin,000);
    }
       if (sel==3){
    analogWrite(redPin,153);
    analogWrite(greenPin,051);
    analogWrite(bluePin,255);
    }
       if (sel==4){
    analogWrite(redPin,000);
    analogWrite(greenPin,255);
    analogWrite(bluePin,128);
    }
       if (sel==5){
    analogWrite(redPin,255);
    analogWrite(greenPin,032);
    analogWrite(bluePin,032);
    } 
           if (sel==6){
    analogWrite(redPin,000);
    analogWrite(greenPin,000);
    analogWrite(bluePin,000);
    } 

} es el mismo circuito para ambos led rgb 



Programa 5

29/11/2022     "Sensor de Aproximacion 1"

#define echoPin 7
#define triggerPin 8
#define ledPin 13
int delaymili = 500;
int maximumRangeCm = 200;
int minimumRangeCm = 0;
long duration, distanceCm;
void setup() {
  Serial.begin(9600);
  pinMode(triggerPin, OUTPUT);
  pinMode(echoPin, INPUT);
  pinMode(ledPin, OUTPUT);
}
void loop() {
  initTrigger();
  duration = pulseIn(echoPin, HIGH);
  distanceCm = microsecCm(duration);
  if (distanceCm >= maximumRangeCm || distanceCm <= minimumRangeCm){
    Serial.println("Out of range");
    digitalWrite(ledPin, HIGH);
  }
  else {
    digitalWrite(ledPin, LOW);
    Serial.print("Distance in cm: ");
    Serial.println(distanceCm);
    delay(delaymili);
  }
}
long microsecCm(long microsecond) {
  return microsecond / 58;
}
void initTrigger() {
  digitalWrite(triggerPin, LOW);
 
  delayMicroseconds(2);
  digitalWrite(triggerPin, HIGH);
  delayMicroseconds(10);
  digitalWrite(triggerPin, LOW);
}

es este circuto solamente que sin los leds 




Programa 6

29/11/2022     "Sensor de Aproximacion 2"
#define echoPin 7
#define triggerPin 8
#define ledPin 13
int delaymili = 500;
int maximumRangeCm = 200;
int minimumRangeCm = 0;
long duration, distanceCm;
const int lr=12;
const int lv=11;
const int la=10;



void setup() {
  Serial.begin(9600);
  pinMode(triggerPin, OUTPUT);
  pinMode(echoPin, INPUT);
  pinMode(ledPin, OUTPUT);



 pinMode(lr,OUTPUT);
pinMode(lv,OUTPUT);
pinMode(la,OUTPUT);
}
void loop() {
  initTrigger();
  duration = pulseIn(echoPin, HIGH);
  distanceCm = microsecCm(duration);
  if (distanceCm >= maximumRangeCm || distanceCm <= minimumRangeCm){
    Serial.println("Out of range");
    digitalWrite(ledPin, HIGH);
  }
  else {
    digitalWrite(ledPin, LOW);
    Serial.print("Distance in cm: ");
    Serial.println(distanceCm);
    delay(delaymili);
  }



 if(distanceCm>=0 && distanceCm<=8){
  Serial.print("!!PELIGRO!!  ") ;
  digitalWrite(lr,HIGH);
  digitalWrite(lv,LOW);
  digitalWrite(la,LOW);
  }
  else if(distanceCm>8 && distanceCm<=16){
   Serial.print("Precaucion!  ") ;
  digitalWrite(lr,LOW);
  digitalWrite(lv,LOW);
  digitalWrite(la,HIGH);
  }
  else if(distanceCm>16 && distanceCm<200){
    Serial.print("Zona segura  ") ;
  digitalWrite(lr,LOW);
  digitalWrite(lv,HIGH);
  digitalWrite(la,LOW);
  }




  
}
long microsecCm(long microsecond) {
  return microsecond / 58;
}
void initTrigger() {
  digitalWrite(triggerPin, LOW);

  delayMicroseconds(2);
  digitalWrite(triggerPin, HIGH);
  delayMicroseconds(10);
  digitalWrite(triggerPin, LOW);
}



Programa 7

01/12/2022     "Sensor de Humedad  1"
#include <SimpleDHT.h>
//VCC: 5V O 3V
//GND: GND
//DATA: 2
int pdatos=2;//Advertencia 
SimpleDHT11 dht11;

 

void setup() {
  // put your setup code here, to run once:
  Serial.begin(9600);
}

 

void loop() {
  // put your main code here, to run repeatedly:
 Serial.println("*==============+++==============*");
 Serial.println("Ejemplo de temperatura y humedad ");
//lean datos
byte temperatura=0;
byte humedad=0;
byte data[40]={0};
if(dht11.read(pdatos, &temperatura, &humedad, data)){
  Serial.print("Error de comunicacion");
}
Serial.println("Muestra");
Serial.print((int)temperatura); Serial.println("°C");
Serial.print((int)humedad); Serial.println("%");

 

delay(5000);

 

}


Programa 8

02/12/2022     "Sensor de Humedad  2"
#include <SimpleDHT.h>
//VCC: 5V O 3V
//GND: GND
//DATA: 2
int pdatos=2;//Advertencia 
SimpleDHT11 dht11;

 

void setup() {
  // put your setup code here, to run once:
  Serial.begin(9600);
}

 

void loop() {
  // put your main code here, to run repeatedly:
 Serial.println("==============+++==============");
 Serial.println("Ejemplo de temperatura y humedad ");
//lean datos
byte temperatura=0;
byte humedad=0;
byte data[40]={0};
if(dht11.read(pdatos, &temperatura, &humedad, data)){
  Serial.print("Error de comunicacion");
}
Serial.println("Muestra");
Serial.print((int)temperatura); Serial.println("°C");
Serial.print((int)humedad); Serial.println("%");
if (temperatura<-10 && temperatura>15){
Serial.println("Frio");
Serial.println("         () ");
Serial.println("        (_) ");
Serial.println("       (___) ");
Serial.println("      (____) ");
Serial.println("     (______)   ");
Serial.println("      \/\/\/\/\/");
Serial.println("       \/\/\/\/");
Serial.println("        \/\/\/");
Serial.println("         \/\/");
Serial.println("          \/");

else{
  if(temperatura<20 && temperatura>50){
Serial.println("Calor");
Serial.println("     O      , U  ");
Serial.println("    |_ ______ _|__");
Serial.println("|_||               |||__");
Serial.println("_|||       )  '    ||_|");
Serial.println(" |||    ( ()\(     |||_");
Serial.println("_|||  ( ,|,(X)'    ||_#");
Serial.println("|_|| /,)/|`\``\\\  |||_/\");

  }
}

e igual que en los anteriores el circuito era el mismo simplemente cambiándole cosas al código 




ACTIVIDADES DEL PDF 

Actividad 1 

"Mapa conceptual"

Tema:   6.1 Tipos de puertos de comunicación 
6.2 Especificaciones de los puertos de comunicación 
Fecha: 06/12/2022 
Nombre: Edgar Omar Claderón Meza


Elabore un  mapa conceptual solo con los terminos de los temas 




Actividad 2 

"Programa"

Tema: 6.3 Envió y recepción  de datos a través de un puerto de comunicación  
6.2 Especificaciones de los puertos de comunicación 
Fecha: 06/12/2022 
Nombre: Edgar Omar Calderón Meza


Elabore un programa que encienda el color de la luz dependiendo de los rango numéricos que del usuario 1-10 Azul, 11-20 verde, 21-30 rosa, 31-40 Amarillo, 41 en delante rojo 

int la=13;
int lv=12;
int lb=10;
int ly=9;
int lr=8;
int num;
void setup() {
  // put your setup code here, to run once:
Serial.begin (9600);
pinMode (la,OUTPUT);
pinMode (lv,OUTPUT);
pinMode (lb,OUTPUT);
pinMode (ly,OUTPUT);
pinMode (lr,OUTPUT);
}

void loop() {
  // put your main code here, to run repeatedly:
if (Serial.available()>0){
  Serial.println("Ingresa un numero");
  num=Serial.parseInt ();
  Serial.println(num);
if (num>=1 && num<=10)
{
 digitalWrite(la,HIGH);
 digitalWrite(lv,LOW);
 digitalWrite(lb,LOW); 
 digitalWrite(ly,LOW);
 digitalWrite(lr,LOW); 
}
else
{ if(num>=11 && num<=20)
  {
 digitalWrite(la,LOW);
 digitalWrite(lv,HIGH);
 digitalWrite(lb,LOW); 
 digitalWrite(ly,LOW);
 digitalWrite(lr,LOW); 
 delay (250); 
  }
else
{ if(num>=21 && num<=30)
  {
 digitalWrite(la,LOW);
 digitalWrite(lv,LOW);
 digitalWrite(lb,HIGH); 
 digitalWrite(ly,LOW);
 digitalWrite(lr,LOW); 
  delay (250);
  }
else
{ if(num>=31 && num<=40)
  { 
 digitalWrite(la,LOW);
 digitalWrite(lv,LOW);
 digitalWrite(lb,LOW); 
 digitalWrite(ly,HIGH);
 digitalWrite(lr,LOW); 
 delay (250);
  } 
else{
if (num>=41) {
 digitalWrite(la,LOW);
 digitalWrite(lv,LOW);
 digitalWrite(lb,LOW); 
 digitalWrite(ly,LOW);
 digitalWrite(lr,HIGH);   
} 
}
  }
  } 
}
}
} 




Comentarios